Skip to content

Chimney Liner Installation in Brooklyn

Serving Brooklyn and nearby cities. Tell us about the job and we’ll call you back to confirm the details.

Tell us what’s going on

Prefer to talk? (361) 329-4790

The short answer

You likely need a new chimney liner if you notice smoke smells, poor draft, tile or brick debris in the firebox, or water and white staining around the chimney, or if you have switched fuels or appliances. NorthStar's certified technicians inspect the flue with a camera, clean it, and install a liner sized for your appliance, following the NFPA 211 standard.

A chimney liner is the protective channel inside your flue that carries smoke and exhaust gases up and out of your home. It keeps heat away from the surrounding brick and framing, and it shields the masonry from acidic exhaust. Many Brooklyn rowhouses, brownstones and multi-family buildings still have their original clay tile liners, or no liner at all. Plenty of them now vent gas boilers or water heaters that the flue was never designed for. NorthStar Chimney Services installs new chimney liners in homes across Brooklyn and nearby neighborhoods. This page covers the signs of a failing liner, what our installation includes, how our certified crew works in your home and on your roof, and what to expect from start to finish.

Signs you need a new chimney liner

Liner damage usually happens out of sight inside the chimney, so most owners notice the side effects first. Cracked clay tiles, open joints and crumbling mortar let exhaust, heat and moisture reach places they shouldn't. If you notice any of the following, have the flue inspected before you use it again.

A liner also becomes a question whenever your heating setup changes. If you have switched fuels or installed a new boiler, furnace, stove or water heater, the existing flue may not be the right size or material for the new appliance.

  • A smoke or creosote smell in the house, especially on humid days or when the fireplace isn't in use
  • Poor draft: smoke rolling into the room, fires that are hard to start, or a boiler or water heater that struggles to vent
  • Pieces of clay tile, mortar or brick flakes collecting in the firebox or at the cleanout door
  • White staining on the brick, inside or outside, which shows that moisture is moving through the masonry
  • Water in the firebox, or damp spots and peeling paint on walls next to the chimney

What's included in a liner installation

Every installation follows the same core steps. We adjust them to fit your chimney and the appliance it serves.

  • Camera inspection of the existing flue to document cracks, gaps, blockages and deterioration
  • Cleaning the flue to remove soot, creosote and loose debris before any work begins
  • Measuring the flue so the new liner is sized correctly for your fireplace, stove or heating appliance
  • Removing broken tile or obstructions where needed so the new liner has a clear path
  • Installing a liner suited to your fuel type, from the appliance connection to the top of the chimney
  • Insulating the liner where the application calls for it
  • Fitting and sealing the top plate, rain cap and appliance connections
  • A final draft check and camera pass to confirm the liner is clear and secure
  • Before-and-after photos and a written summary of the work

How our crew works inside your home and on the roof

Indoors, our technicians lay drop cloths from your entry to the work area and seal off the fireplace opening or appliance connection before cleaning starts. HEPA vacuums run throughout the job to capture soot and fine dust at the source. Rotary brushes clean the flue walls so the camera gets a clear view and the new liner can pass through without snagging.

On the roof, the crew sets up safely, checks the chimney crown and flashing, and feeds the liner down from the top. Brooklyn roofs vary widely, from flat rowhouse roofs reached through a hatch to steep pitches that need ladders and extra safety gear, so we confirm access before the install day. When the work is done, we clean up, haul away old tile and packaging, and walk you through what we did.

The standard we follow

Our work follows NFPA 211, the national standard that calls for chimneys, fireplaces and vents to be inspected once a year. Chimney professionals use three inspection levels. Level 1 applies when nothing about the system has changed. Level 2 applies when the system changes, such as a new appliance or a switch of fuel, or when the home is sold. Level 3 applies when a hidden hazard can only be reached by opening part of the chimney or building.

Liner work often follows a Level 2 situation. That is especially common in New York City when a building converts its boiler from oil to gas. The chimney has to be evaluated as part of that conversion, and a new liner is often needed, because gas exhaust produces acidic condensate that can corrode a masonry flue.

What affects the price

Every chimney is different, so we give you a written estimate after we have seen yours. The main factors are:

Each item is explained on the estimate, so you can see exactly what the work involves before you approve it.

  • Chimney height and roof access, including whether a hatch, ladders or extra safety setup is needed
  • Fuel type and appliance, since wood, gas and oil each call for different liner materials
  • Flue size, shape and condition, including bends, offsets or broken tile that must be removed
  • How much soot, creosote or debris has built up and needs to be cleaned out first
  • Whether a camera inspection, masonry repair, crown work or a new cap is needed

How a visit works

It starts with your call or online request. We ask about your home, the chimney and the appliance it serves, then schedule an inspection. During that visit, a certified technician inspects the flue, reviews the camera footage with you, and explains whether a liner is needed and why.

If you decide to go ahead, we schedule the installation. Many liners can be installed in a single day, though tall or complex chimneys can take longer. At the end, we test the draft, clean up, and give you photos and a summary for your records.

Timing matters in the city. New York City's heat season runs from October 1 through May 31, and building owners must keep apartments heated to the city's minimum temperatures during that period. If you own a multi-family building or are planning a boiler conversion, booking liner work in late spring or summer helps you avoid interrupting heat for tenants.

Chimney Liner Installation by city

What to expect

How a visit goes

  1. Look first, then recommend

    We inspect and photograph the system before suggesting any repair, so recommendations are based on what is actually there.

  2. Clear, written pricing

    You receive a written price for the agreed scope before work begins, and we do not add items without talking to you first.

  3. Clean, careful work inside your home

    We cover floors and furniture, contain soot and dust, and leave the work area clean when we finish.

FAQ

Common questions

Don’t see your question? Call (361) 329-4790 and we’ll talk it through.

Do I need a new liner if I'm converting my boiler from oil to gas?

Often, yes. In New York City, the chimney has to be evaluated when a building converts from oil to gas, and a new liner is frequently needed because gas exhaust produces acidic condensate that can corrode a masonry flue. An inspection will tell you for sure.

Can I keep using my fireplace if the clay tile liner is cracked?

We recommend you stop using it until it has been inspected. Cracks and gaps can let heat and exhaust reach the masonry and nearby framing. A camera inspection shows how serious the damage is and whether relining is the right fix.

How long does a chimney liner installation take?

Many installations are finished in one day. Tall chimneys, difficult roof access, bends in the flue, or broken tile that has to be removed can add time. We give you an expected timeline after the inspection.

Will the installation make a mess in my home?

We work to keep it clean. The crew lays drop cloths, seals off the fireplace or appliance opening, and runs HEPA vacuums throughout the job. Most of the liner work happens from the roof, and we clean up before we leave.

Do you install liners for wood stoves, inserts and water heaters, not just fireplaces?

Yes. We install liners for fireplaces, wood stoves, inserts, boilers, furnaces and water heaters. The liner material and size depend on the fuel type and the appliance it serves.

How often should my chimney be inspected after a new liner goes in?

The NFPA 211 standard calls for chimneys, fireplaces and vents to be inspected once a year. A yearly inspection catches buildup, damage or water problems early, whether your liner is new or old.

Schedule a Chimney or Vent Inspection

Tell us what you are noticing and where you are in Brooklyn. We will inspect, show you photos of what we find, and give you a written price before any work begins.

Call (361) 329-4790 Request Service